Strength Systems

Optima Plus Smith Rack

Owner's Manual

• Chapter 1: Safety
  • 1.1: Safety Information
  • 1.2: Access Control
  • 1.3: Installation
  • 1.4: Proper Usage
  • 1.5: Inspection
  • 1.6: Operating Warnings
  • 1.7: Selectorized Weight Stack Systems
  • 1.8: Warnings and Cautions
  • 1.9: Product Labels
  • 1.10: Label Locations
    • 1.10.1: Attached Cable Crossover (PP-ACO)
    • 1.10.2: Free Standing Cable Crossover (PP-ACOFS)
    • 1.10.3: Dip/Chin Assist (PP-ADC)
    • 1.10.4: Adjustable Cable Column (PP-AP)
    • 1.10.5: Adjustable Pulley 4:1 (PP-AP41)
    • 1.10.6: Embedded Cable Crossover (PP-AXO)
    • 1.10.7: Crossover Boom (PP-BM)
    • 1.10.8: Boxing (PP-BX)
    • 1.10.9: Core (PP-CORE)
    • 1.10.10: Dip (PP-DIP)
    • 1.10.11: Dual Pulley High (PP-DPH)
    • 1.10.12: Dual Pulley Low (PP-DPL)
    • 1.10.13: Attached High Low Crossover (PP-FCO)
    • 1.10.14: Embedded High Low Crossover (PP-FXO)
    • 1.10.15: Handle Accessory Rack (PP-HAR)
    • 1.10.16: High Low (PP-HL)
    • 1.10.17: Lat Pull (PP-LP)
    • 1.10.18: Dual Handle Lat Pull (PP-LPD)
    • 1.10.19: Power Pivot (PP-PP)
    • 1.10.20: Rope Pull - Power Pivot (PP-RP)
    • 1.10.21: Rope Pull (PP-RPL)
    • 1.10.22: Low Row (PP-RW)
    • 1.10.23: Dual Handle Low Row (PP-RWD)
    • 1.10.24: Stall Bars (PP-SB)
    • 1.10.25: Storage Station (PP-SC)
    • 1.10.26: Step (PP-STP)
    • 1.10.27: Storage Connector (PP-SX)
    • 1.10.28: Triceps Pushdown (PP-TP)
• Chapter 2: Assembly
  • 2.1: Packing and Shipping Options
  • 2.2: Assembly Procedure - R Series Lower Body
    • 2.2.1: Verify Parts List Shown Below
    • 2.2.2: Tools Required
    • 2.2.3: Lift and Move Unit
    • 2.2.4: Install Console Weldment
    • 2.2.5: Note for Single Box Option
    • 2.2.6: Install Cables to Console
    • 2.2.7: Install Console to Console Weldment
    • 2.2.8: Install Console Cables to Base (Basic Cabling)
    • 2.2.9: Install Console Cables to Base (Advanced Cabling)
    • 2.2.10: Install Accessory Tray Base
    • 2.2.11: Install Accessory Tray Top
    • 2.2.12: Install Accessory Tray Bottom
    • 2.2.13: Install Side Handles
    • 2.2.14: Install Foot Pads
    • 2.2.15: Visually Inspect Unit
    • 2.2.16: Level Unit
  • 2.3: Assembly Procedure - R Series Total Body
    • 2.3.1: Verify Parts List Shown Below
    • 2.3.2: Tools Required
    • 2.3.3: Lift and Move Unit
    • 2.3.4: Install Console Weldment
    • 2.3.5: Note for Single Box Option
    • 2.3.6: Install Cables to Console
    • 2.3.7: Install Console to Console Weldment
    • 2.3.8: Install Console Cables to Base (Basic Cabling)
    • 2.3.9: Install Console Cables to Base (Advanced Cabling)
    • 2.3.10: Install Accessory Tray Base
    • 2.3.11: Install Accessory Tray Top
    • 2.3.12: Install Accessory Tray Bottom
    • 2.3.13: Install Rear Covers
    • 2.3.14: Remove Left and Right Handle Assembly
    • 2.3.15: Install Left Linkage Rod
    • 2.3.16: Install Right Linkage Rod
    • 2.3.17: Install Contact Heart Rate Cable
    • 2.3.18: Install Foot Pads
    • 2.3.19: Visually Inspect Unit
    • 2.3.20: Level Unit
• Chapter 3: Product Information
  • 3.1: Specifications
• Chapter 4: Exercise
  • 4.1: General Exercise Information
  • 4.2: Performing the Exercises
• Chapter 5: Maintenance Procedures
  • 5.1: Maintenance Schedule
• Chapter 6: Warranty
  • 6.1: What is Covered
  • 6.2: Who is Covered
  • 6.3: Who Pays Transportation and Insurance For Service
  • 6.4: What We Will Do To Correct Covered Defects
  • 6.5: What is Not Covered
  • 6.6: Owner's Manual
  • 6.7: Exclusive Warranty
  • 6.8: Changes in Warranty Not Authorized
  • 6.9: Effects of State Laws
  • 6.10: Warranty Coverage
• Chapter 7: Bolt to Floor Guide
  • 7.1: Introduction
  • 7.2: Delivery and Installation Tips
  • 7.3: Anchor Type - Static
  • 7.4: Anchor Specifications
  • 7.5: Pullout Force
  • 7.6: Tools Required
    • 7.6.1: Static Anchor
  • 7.7: Static Anchor Procedure
  • 7.8: Foot Dimensions