Home page logo
Home page logo
LifeFitness.com
  • Support Hub
  • Parts
  • Table of Contents
  • العربية — Arabic Deutsche Español English français italiano 日本語 — Japanese Korean Nederlands português русский — Russian Turkey 中文 — Chinese
  • Log In

Atmos Treadmill and Atmos Home Edition Treadmill

Life FitnessAtmos Treadmill and Atmos Home Edition TreadmillOwner's Manual / Assembly Instructions
  • Chapter 1: Additional Information
    • 1.1: Link to Additional Information Online
  • Chapter 2: Getting Started
    • 2.1: Safety Instructions
    • 2.2: Consignes de Sécurité
    • 2.3: Set-Up
      • 2.3.1: Electrical Power Requirements
      • 2.3.2: Grounding Instructions
      • 2.3.3: How to Position and Stabilize the Unit
      • 2.3.4: Safety Clearances
      • 2.3.5: Turning the Unit On / Off
    • 2.4: Immobilization Method - SL Console
    • 2.5: Immobilization Method - SE4 Console
  • Chapter 3: Product Overview
    • 3.1: Product Features
    • 3.2: Mounting and Dismounting the Unit
    • 3.3: User Position
    • 3.4: Using and Testing the Emergency Stop System
    • 3.5: Product Labels
    • 3.6: Label Locations
  • Chapter 4: Assembly
    • 4.1: Hardware
    • 4.2: Required Tools
  • Chapter 5: Assembly Procedure
    • 5.1: Unpacking and Disposal of Packaging
    • 5.2: Remove Motor Cover Top Shroud
    • 5.3: Attach Upright Weldments to Base
    • 5.4: Attach Bridge Weldment to Upright Weldments
    • 5.5: Tighten Screws Securing Upright Weldments to Base
    • 5.6: Cable Connections: Base to MDB PC Board
    • 5.7: Ferrite Installation - Motor Pan
    • 5.8: Install SE4 Cables to Comport Panel
    • 5.9: Attach Console Weldment to Bridge Weldment
    • 5.10: Install Ground Cable
    • 5.11: Attach Upper Bridge Shroud to Bridge Weldment
    • 5.12: Attach Lower Bridge Shroud to Bridge Weldment
    • 5.13: Attach Console Lower Shroud
    • 5.14: Ferrite Installation - Bottom of Console Weldment
    • 5.15: Cable Connections: Base to Console
    • 5.16: Attach Console: SE4
    • 5.17: Attach Console: SL
    • 5.18: Attach Console Back Shroud to Console Weldment
    • 5.19: Secure Motor Cover Front Shroud
    • 5.20: SE4 Power Supply Cable and Ferrite Installation
    • 5.21: Secure Motor Cover Top Shroud
    • 5.22: Attach Power Cord
    • 5.23: Test Unit For Proper Operation
  • Chapter 6: Specifications
    • 6.1: Specifications
  • Chapter 7: Service and Technical Data
    • 7.1: Preventive Maintenance Tips
    • 7.2: Approved and Compatible Cleaners
    • 7.3: Preventive Maintenance Schedule
    • 7.4: Troubleshooting the Treadmill
    • 7.5: How To's
      • 7.5.1: Knowledge Base
      • 7.5.2: How To Obtain Product Service
      • 7.5.3: How to Adjust and Tension the Striding Belt
      • 7.5.4: Belt Tensioning Bolts
      • 7.5.5: Tensioning an Existing Striding Belt
      • 7.5.6: Tracking (Centering) a Striding Belt
    • 7.6: Software Updates
  • Chapter 8: Warranty
    • 8.1: Warranty Information
  • Chapter 9: Release Notes
    • 9.1: Updates to Manual

Getting Started

In this section:

  1. Safety Instructions
  2. Consignes de Sécurité
  3. Set-Up
  4. Immobilization Method - SL Console
    The purpose of immobilizing the treadmill is to prevent unauthorized use. The system causes immobilization of the treadmill when activated.
  5. Immobilization Method - SE4 Console
    The purpose of immobilizing the unit is to prevent unauthorized use. The system causes immobilization of the unit when activated.

Was this helpful?

Thanks!

Service Hub

  • Self Service
  • Order Parts
  • Warranties

Additional Support

  • Become a Service Partner
  • Request Service
  • Product Registration
  • Contact Us
  • Privacy Policy
  • Terms and Conditions

Copyright © 2026 Life Fitness

Building One-Page View

This might take a few seconds.